The Fundamentals of Plumbing Knowledge for Bathtub Installation
The Fundamentals of Plumbing Knowledge for Bathtub Installation
Blog Article
The writer is making a few great annotation about Tools You Need to Install a New Bathtub as a whole in the article which follows.
Installing a tub isn't specifically rocket science, however it does require strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is also a reasonably tough project. If the old tub is readily obtainable, the task can move easily; if you need to open a wall surface to remove the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a house handyman's skills, although you will require an assistant to vacate the old bathtub and set in the new one. Make certain you have actually qualified on your own for the task and are comfortable attempting it. Rather than employing a professional to take control of a halfway-completed task, it is far better to consider utilizing one prior to you begin. Possibilities are you may need an expert plumber to make tube connections.
This article will assist you set up a brand-new tub in your restroom if you have already purchased a brand-new tub and also don't need to alter the arrangement of your previous water pipes.
Your devices as well as product checklist should make up the following:
Preparing for the Installation
To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets unit to stop stress on the bath tub.
Fit the adaptable tap adapters to the bottom of both taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be rather problematic as a result of the restricted access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been gotten rid of, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Prior to proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wood boards are practical in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by examining the level and readjusting the feet on the bathtub till the spirit level checks out level.
To mount taps, fit all-time low of the furthest versatile tap port to the appropriate supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the water system and also inspect all joints and also new pipework for leakages as well as tighten them if required. Fill up the bathtub as well as additionally inspect the overflow electrical outlet and also the regular outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the bath tub should wait till the tub has been used a minimum of when as this will certainly settle it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines remain in location between the faucet and the sink. Protect the faucet in place with the producer supplied backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The former kind must be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to split an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, bring about problems with moisture and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealer can break fairly early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that piece of writing about Installing A Bathtub while surfing around the internet. In case you enjoyed reading our page please remember to share it. Thank-you for taking the time to read it.
About Report this page